• Toyota Rav4 1997 Manual Transmission Speed Sensor Installation In A Th400
• Toyota Rav4 1997 Manual Transmission Speed Sensor Installation On Spin Bike

Components

Sep 26, 2016  Besides, I remember 3 wires at the actual speed sensor, located on the transmission, and not just 2 as shown in the schematic:disappoin ). I've even gone and traced back all the input/outputs to the ECU, but I still can't figure out how the ECU is wired to the speed sensor on the transmission. Inspect speed sensor nc. Measure the resistance of the sensor. Standard resistance. Install speed sensor nc. Coat a new o-ring with atf. Install the o-ring to the sensor. Install the sensor with the bolt. Torque: 11 n.m (112 kgf.cm, 8 ft.Lbf) Connect the sensor connector. Install speed sensor nt. Coat a new o-ring with atf. Jun 22, 2012  location for toyota rav4 vehicle speed sensor - Toyota 2004 RAV4 question. Search Fixya. Coat a new O-ring with ATF and install it to the vehicle speed sensor. Install the speedometer driven gear to the vehicle speed sensor and clip. May 31, 2009 1997 Toyota RAV4. 2 Answers Where is the Air Fuel Sensor Located on 1999 Toyota RAV4?

Removal

1. Buy a 1997 Toyota RAV4 Manual Trans Speed Sensor at discount prices. Choose top quality brands Beck Arnley. Discount Auto Parts and Accessories. Back - 1997 Toyota RAV4 Transmission Manual Trans Speed Sensor. 1997 Toyota RAV4 Manual Trans Speed Sensor Review Fitment Notes to Ensure Proper Fit ‹ Change Part / Category.
2. View and Download Toyota RAV4 1997 owner's manual online. Toyota RAV4 1997. RAV4 1997 Automobile pdf manual download.
3. Well, I had a line fail from the E250F 4x4 5 speed manual transmission to the oil cooler, dumped the fluid and toasted the transmission. I had just replaced every hose under the hood with the exception of those two hoses. Only because I had to order them and they had not been delivered yet.
4. AutoZone Repair Guide for your Drive Train Manual Transmission Transmission Removal & Installation. Automatic Transaxle. Remove the wiring from the speed sensor and back-up light switch. Remove the ground cable from the transaxle. Manual Transmission Transmission Removal & Installation AutoZone.com. Product Search Search suggestions.

1. Disconnect cable from negative battery terminal

Caution:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

2. Remove battery

1. Loosen the nut and remove the bolt and battery clamp.
2. Remove the battery.
3. Remove the battery tray.
4. Remove the 4 bolts and battery carrier.
5. Remove the 2 bolts and battery bracket reinforcement.

3. Remove speed sensor nt

1. Disconnect the sensor connector.
2. Remove the bolt and sensor.
3. Remove the o-ring from the sensor.

4. Remove speed sensor nc

1. Disconnect the sensor connector.
2. Remove the bolt and sensor.
3. Remove the o-ring from the sensor.

Inspection

1. Inspect speed sensor nt

Measure the resistance of the sensor.

Standard resistance

2. Inspect speed sensor nc

Measure the resistance of the sensor.

Standard resistance

Installation

1. Install speed sensor nc

1. Coat a new o-ring with atf.
2. Install the o-ring to the sensor.
3. Install the sensor with the bolt.

Toyota Rav4 1997 Manual Transmission Speed Sensor Installation In A Th400

Torque: 11 n*m (112 kgf*cm, 8 ft.*Lbf)

4. Connect the sensor connector.

2. Install speed sensor nt

1. Coat a new o-ring with atf.
2. Install the o-ring to the sensor.
3. Install the sensor with the bolt.

Torque: 11 n*m (112 kgf*cm, 8 ft.*Lbf)

4. Connect the sensor connector.

Toyota Rav4 1997 Manual Transmission Speed Sensor Installation On Spin Bike

3. Install battery

1. Install the battery bracket reinforcement with the 2 bolts.

Torque: 20 n*m (204 kgf*cm, 15 ft.*Lbf)

2. Install the battery carrier with the 4 bolts.

Torque: 20 n*m (204 kgf*cm, 15 ft.*Lbf)

3. Install the battery tray.
4. Install the battery with the battery clamp.

Torque: 8.5 N*m (87 kgf*cm, 75 in.*Lbf) for bolt

5.0 N*m (51 kgf*cm, 44 in.*Lbf) for nut

4. Connect cable to negative battery terminal

Other materials:

Heated oxygen sensor
Components Removal Disconnect cable from negative battery terminal Caution: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. Remove heated oxygen sensor (for bank 1 sensor 2) ...

Downhill assist control operation switch (test mode dtc)
Description The downhill assist control switch is connected to the skid control ecu in the abs and traction actuator. Dtc c1379/74 can be detected when the downhill assist control switch sends the downhill assist control switch signal or test mode ends. Dtc c1379/74 is output only in t ...

Tc and cg terminal circuit
Description Dtc output mode is set by connecting terminals tc and cg of the dlc3. The dtcs are displayed by blinking the srs warning light. Hint: Make sure that dtc b1281 has not been output. If dtc b1281 has been output, refer to the multiplex communication system. When each warning ...